System Test
Testing conducted on a complete, integrated system to evaluate the system's compliance with its specified requirements .
See Also: Systems, Equipment, Test Systems, System Integrators
-
product
Test Line • Perforation counter
Perforation counter PZ 3
The perforation counter PZ 3 can be used among other things in the production of plastic bags and garbage bags. By the non-contact perforation detection, for example, the number of bags / batches can be determined and the roll change can be initiated.
-
product
Portable Data Acquisition & Analysis System
LapCAT III
# 4, 8, or 16 channels# 1 MHz aggregate 12 bit sampling. Resolution is 0.024% of full scale# 13 recording durations, user selected: 132 msec to 1320 sec# Digital Triggering from any channel, with +/- slope or window# 6 full scale gain ranges, user selected: 0.4, 1, 2, 4, 10, and 20 volts full scale - with a 10mV/g accelerometer these equal 40g, 100g, 200g, 400g 1000g and 2000g full scale - higher or lower ranges by different sensor selection
-
product
Neutron Flux Monitoring Systems
To monitor reactor core neutron flux and provide indication during all modes of reactor operation, and to provide trip signals to the Reactor Protection System (RPS) and the Reactor Manual Control System (RMCS).
-
product
Portable Converged Networks Test Set
TX Series
The VeEX TX product series offers a complete test solution for Next Generation of Transport, Metro and Carrier Ethernet Testing. Color graphical display assisted with touch panel enables users tapping through the test configuration and accessing complex overhead bits and bytes. Features include APS, TDM, pointer adjustment, pulse mask analysis, G.821/G.826/M.2100, histogram, and overhead access.
-
product
900 Hz to 110 GHz PNA MM-Wave System
N5290A
Single-sweep solution with compact frequency extenders Purchase as a single product solution Accurate leveled power can be applied to the device, providing the ability to sweep power Available various software application for detail analysis Every spec verified, adjustments included Lock in support & peak performance from the start
-
product
Engineering Test & Development Tools
Besides DG’s aftermarket diagnostic tools, DG Technologies also offers several engineering tools for vehicle network development. DG’s hardware and software products are used by a variety of engineering customers such as test engineers, production engineers, and fiber optic testers. Our customers use DG interfaces for manipulating messages, datalogging, and ECU end-of-line testing over various multiplex networks.
-
product
Sensors And MEMS Test
Easy docking and undocking of the MEMS modules to the standard test handler whether Gravity, Pick and Place or Test in StripTest in the complete tri-temp range for ambient, hot and cold (automotive certified)Easily convertible to other packagesDownscaled stand-alone engineering set-up availableGlobal support by experienced Cohu Field Service and Applications staff
-
product
Fluidic Dispensing Systems
Parker's fluidic-dispensing systems and related products include intracellular microinjection dispense systems for life science research and development as well as emulsion mixers that provide constant, accurate mix ratios of soluble oil and water for mining applications.
-
product
Signal Integrity Test Products
RoBAT SCARA-TDR-M
*Fully automatic TDR tester for bare and assembled PCBs*2 – 24 Port Ultra-compact TDR units*Full range of TDR tests and measurements available*100% test in a production environment*Custom modules with automatic tool changer
-
product
In-circuit Test
Medalist i1000 Systems
Cover Extend Technology (CET) is now supported on the Medalist i1000D. The i1000D only requires a VTEP MUX card to enable CET. If you are already using test fixtures with VTEP MUX cards , you can now implement CET without any fixture modification. Simply add new VTEP probes to devices that were previously not testable. This greatly reduces implementation efforts.
-
product
Transducer Calibrator Systems
Unholtz-Dickie Calibration Systems have earned their place in industry as the standard for calibrating accelerometers and velocity transducers. The Models 660C & 680C are UD''s latest generation of automatic calibration systems, both utilizing the expanded features of the i5 based APEX SL Windows vibration control system.
-
product
Ozone Test Chambers
Labodam Ozone Test Chambers are designed to detect the concentration of ozone while requiring low maintenance, having well-built corrosion resistant bodies, and while utilizing noiseless generators.
-
product
Salt Spray Test Chamber
Salt water spraying/corrosive resistant machine are specialized to test the performance of the products for its surfaces of various materials after treatment of corrosive protection by means of painting, coating, galvanizing, anodizing and of lubricant.
-
product
Quantum Efficiency Measurement Systems
Newest generation of quantum efficiency (yield) measurement tool, which allows the user to determine QE of powders, liquids, solids and films. An optically optimized geometry using an integration hemisphere and low stray light array spectrometer enables world class measurements and new applications.
-
product
Portable Three Phase Energy Meter Test Set
SY3632
Hong Kong Songyang Industrial Ltd.
The SY3630 Energy Meter Testing Instrument is used to calibrate three phase, single phase, active or reactive energy meter under work, and also it can be used as voltage, current and power meter to measure AC parameter of three phase power line. Same as ZERA and MTE. Of course our price is very reasonable.
-
product
System
SYS-24
The system shown here was built for a customer to be used in metallization, a common use for many smaller systems. It is also fully capable of performing optical coatings when equipped to do so. This particular system came equipped with a 16" APD ISO Flange mounted cyropump, and a Varian tri-scroll for roughing. The cooling tubes for the crystals as well as the drive motor for the parts holder can be seen on the top of the chamber.
-
product
Automated Titration Analysis Systems
MANTECH is a leading manufacturer of multi-parameter and titration analysis systems. We can deliver custom analysis systems that perform the following functions: pH, Chloride, Oxygen, Turbidity, Alkalinity, Fluoride, Oxidation-Reduction Potential (ORP), Nitrate, Electrical Conductivity, Color, Salinity, Total Hardness, Acidity, Ammonia, Temperature and Soil pH & Conductivity.
-
product
Remote Indicator System
LineTroll R110CQ
The fault indicator use a 2.4GHz ISM band short-range radio to communicate with the collector mounted on the pole. The collector communicates with up to 9 fault indicators. Both the indicators and the collector are powered by long-life lithium batteries for long and maintenance free operation.
-
product
All-In-One Battery Testing System
Integrating charge-discharge and temperature testing into one.
-
product
Fine Tip Test Probes
U1164A
Compatible with test leads shipped with U1210, U1240B, U1250, U1270 series of handheld clamp meter and multimeters
-
product
System Components
System components and accessories complete the Bender product portfolio:Coupling devices for ground-fault monitoring at high voltages, analog measuring instruments, power supply units, interface converters and interface repeaters.Please contact us for advice regarding these and other system components.
-
product
Split-type Cable Fault Location System
Weshine Electric Manufacturing Co., Ltd
Electricity networks have had to become more flexible, reacting more quickly to the changes and needs of higher performance. This demand for flexibility is especially true where multiple generation sources occur, such as the intermittent power from renewables like solar and wind energy. While modern SMART grid technology can quickly identify faults in sub-station and generating units, cable faults can still occur anywhere on the network.
-
product
Fused Test Probes with Silicone Test Leads
AL-57FL
Standard Electric Works Co., Ltd
● AL-57FL is an ideal tool which shows the indication of live voltage even with blown fuse.● 2 replaceable fast-acting fuses are built-in. The specs of the fuses are 1000V, 11A with internal rating of 20kA AC/DC.● Provide additional testing protection.● Help to prevent a possible mis-indication when there is voltage present.● CAT III 1000V, CAT IV 600V, 10A with protective cover.● 2mm probe tips, removable 4mm brass caged banana probe tips are also included.● Include High-qu...show more -
product
Avionics Network Simulation Systems
Avionics Interface Technologies
Support for up to 30 Network Interfaces (Fibre Channel & Ethernet)Time Synchronization with IRIG-B & IEEE 1588 Master ClocksFull Data Capture with time stampingData simulation with precise timing & synchronizationNetwork data replay from previously captured trafficPerform Network analysis using AIT's intuitive, easy to use, Ethernet & Fibre Channel simulation tools
-
product
Single Mode & Multimode Test Kit
KI-TK037
1310/1550 nm & 850/1300 nm source & power meter, inspection microscope & cleaning materials with Interchangeable SC & LC connectors
-
product
Cable Continuity Test Fixture
CCT
6 and 8 Wire Cable Continuity Test Fixtures For convienient desk top and bench top The most important features of this cable continuity tester is its ease of use intuitive control functions and durability in a production environment.
-
product
Custom Cryogenic Systems
With our in-house design and manufacturing capabilities, our experienced physicists and engineers are ready to discuss your requirements for any type of cryogenic application.
-
product
Multi-Service Transport Test Solution
MX Series
The VeEX MX product series offer a complete test solution for Metro Ethernet network installation and maintenance. Powerful features such as symmetrical and asymmetrical RFC2544 conformance testing, Multiple independent stream generation, Stacked VLAN (Q-in-Q) and MPLS tagging, and Dual Port Traffic Generation/Analysis are available at 10GBase-R, 1000Base-X and 10/100/1000Base-T test interfaces. Fiber Channel testing at 1Gbps and 2Gbps rates is supported on select models.
-
product
VibA(8) Hand-Arm Vibration System
VK040
Ultra-simple and dedicated to compliance of the Vibration at Work Regulations 2005, this is the perfect option for your Hand-Arm Vibration measurements with the added benefit of being able to add a Whole-Body Seat Pad at any time further down the line.
-
product
Test Management Software
Easy to use to minimal training. Our Test Management Software is powerful enough to accommodate all of your electrical and function testing requirements, whether testing a cable harness or fully equipped vehicle or aircraft.
